CAC / BDP 40GVM Specifications download pdf

5 3 D S --- 9 0 0 --- --- --- 1 1 7 ( 1 1 5 v )

5 3 D S --- 9 0 0 --- --- --- 1 1 8 ( 2 3 0 v )

Installation Instructions

Accessory Condensate Pump

fo r Du ctless S plit Sy stem

Coo ling Only and Heat P ump High Wall Units

(Size 009---036)

NOTE: Read and become familiar with these instructions before

beginning installation.

SAFETY CONSIDERATIONS

Improper installation, adjustment, alteration, service,

maintenance, or use can cause explosion, fire, electrical shock, or

other conditions which may cause death, personal injury, or

property damage. Consult a qualified installer, service agency, or

your distributor or branch for information or assistance. The

qualified installer or agency must use factory--authorized kits or

accessories when modifying this product. Refer to the individual

instructions packaged with the kits or accessories when installing.

Follow all safety codes. Wear safety glasses, protective clothing,

and work gloves. Use quenching cloth for brazing operations.

Have fire extinguisher available. Read these instructions

thoroughly and follow all warnings or cautions included in

literature and attached to the unit. Consult local building codes

and current editions of the National Electrical Code (NEC) NFPA

70. In Canada, refer to current editions of the Canadian electrical

code CSA 22.1.

Recognize safety information. This is the safety--alert symbol

When you see this symbol on the unit and in instructions or

manuals, be alert to the potential for personal injury. Understand

these signal words; DANGER, WARNING, and CAUTION.

These words are used with the safety--alert symbol. DANGER

identifies the most serious hazards which will result in severe

personal injury or death. WARNING signifies hazards which

could result in personal injury or death. CAUTION is used to

identify unsafe practices which would result in minor personal

injury or product and property damage. NOTE is used to

highlight suggestions which will result in enhanced installation,

reliability, or operation.

UNIT OPERATION HAZARD

Failure to follow this caution may result in unit failure

and/or damage.

Always follow instructions properly.

CAUTION

16’ Transparent

Suction Discharge Tubing

Condensate Pump

Assembly

Low Voltage

Power Cord

Transparent

Detection

Unit Vent Tubing

Detection Unit

5/8” Rubber Elbow

Detection Unit

Mounting Bracket

Wire Ties (6)

Mounting Bracket

Power Cable

Adhesive

A12227

Fig. 1 --- Accessory Condensate Pump Kit

Table 1—Accessory Condensate Pump Kit Contents

ITEM QTY

16---ft Transparent Suction/Discharge Tubing 1

Condensate Pump Assembly 1

L o w --- V o l t a g e P o w e r C o r d 1

Transparent Detection Unit Vent Tubing 1

Power Cable 1

Wire Ties 6

Wall Mount Bracket 1

Adhesive 1

Detection Unit Mounting Bracket 1

5/8--- in Rubber Elbow 1

Detection Unit 1

ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal injury

or death.

Before beginning any modification or installation of this kit,

be sure the main electrical disconnect is in the OFF position.

Ensure power is disconnected to the fan coil unit. On some

systems both the fan coil and the outdoor unit may be on the

same disconnect. Tag the disconnect switch with a suitable

warning label. There may be more than one disconnect.

WARNING

1 2 3 4 5 6 ... 11 12

Summary of Contents

Page 1 - Installation Instructions

5 3 D S --- 9 0 0 --- --- --- 1 1 7 ( 1 1 5 v )5 3 D S --- 9 0 0 --- --- --- 1 1 8 ( 2 3 0 v )Installation InstructionsAccessory Condensate Pumpfo r D

Page 2 - INSTALLATION

10NLALALWHTBRNYELBLUA13098Fig. 16 --- 40GVC 9k, 12k (115--1--60) WIRING SCHEMATICNLALALWHTBRNYELBLUA13099Fig. 17 --- 40GVQ 9k, 12k (115--1--60) WIRING

Page 3

11BLUBRNWHTYELA13101Fig. 19 --- 40GVC/Q 18k, 24k, 30k, 36k (208/230--1--60) WIRING SCHEMATICBLUBRNWHTYELA13102Fig. 20 --- 40GVM 9k, 12k, 18k (208/230-

Page 4

12CLEANING AND MAINTENANCEELECTRICAL SHOCK HAZARDFailure to follow this warning could result in personal injuryor death.Disconnect all power to unit t

Page 5

2Table 2—Accessory Package UsageBASE UNITACCES SORY MODEL NUMBER5 3 D S --- 9 0 0 --- --- --- 1 1 7( 1 1 5 --- 1 --- 6 0 )5 3 D S --- 9 0 0 --- --- --

Page 6 - PUMP ALARM BREAKS SIGNAL

35. Connect one end of the low voltage power cord to the tele-phone jack socket in the detection unit and route the cordand transparent drain tubing t

Page 7 - PUMP POWERED FROM INDOOR UNIT

4Table 3—True Flow Rates (Gallons / Hr)53DS--- 900 --- --- --- 117, 118 Condensate Pump Flow RatesRefertoFig.2for(A),(B),(C)Total tube length, 1/4” fl

Page 8

5DETECTIONUNIT5/8" RUBBERHOSEDETECTION UNITMOUNTING BRACKETFAN COIL CONDENSATEDRAIN LINEDETECTIONUNIT VENT TUBINGSUCTION TUBINGLOW VOLTPOWER CORD

Page 9

6WHTBRNYELBLU115-1-60 POWER REQUIRED FOR PUMP PUMP ALARM BREAKS SIGNALOUTDOOR UNITTERMINAL BLOCK115-1-60POWER SUPPLY(from outdoor or dedicated source)

Page 10

7BLUBRNWHTYELPUMP POWERED FROM OUTDOOR UNITPUMP ALARM BREAKS SIGNALOUTDOOR UNITTERMINAL BLOCK208/230-1-60MAIN POWER SUPPLYPUMP208/230-1-60A13106Fig. 1

Page 11

8BLUBRNWHTYELPUMP POWERED FROM INDOOR UNITPUMP ALARM BREAKS SIGNALINDOOR UNITTERMINAL BLOCKBARDTGOYTO OUTDOORUNITA12396Fig. 12 --- (208/230--1--60) WI

Page 12 - CLEANING AND MAINTENANCE

9Pump115-1-60LNALALL1L2SIndoor Unit Terminal BlockGNDL1L2SL1L2Outdoor Unit Terminal BlockGNDField Power Wiring208/230-1-60LegendField Power WiringInte